Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VECTRA® A430 - (LCP+PTFE)-MX25 - Celanese

Check here, which other Vectra datasheets, application examples or technical articles are available in Material Data Center

Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades - Diagrama

Any use of this information falls under the rules of our disclaimer.

Informação do produto

Provides many of the characteristics of A130 with added lubricity. Suitable for applications requiring excellent wear characteristics. Excellent electrical properties at high frequencies. LCP/PTFE blend. Chemical abbreviation according to ISO 1043-1 : LCP Inherently flame retardant FDA compliant version available UL-Listing V-0 in natural and black at 0.43mm thickness per UL 94 flame testing. Relative-Temperature-Index (RTI) according to UL 746B: electrical 130°C, mechanical 130°C. UL = Underwriters Laboratories (USA)

Flammability at thickness h

V-0

-

Características de processamento/físicas	Valor	Unidade	Método de ensaio
ISO Dados
Contração após a moldagem, perpendicular	0.7	%	ISO 294-4, 2577

Propriedades mecânicas	Valor	Unidade	Método de ensaio
ISO Dados
Módulo de tração	7000	MPa	ISO 527
Tensão na ruptura	150	MPa	ISO 527
Deformação na ruptura	5.8	%	ISO 527
Resistência ao impacto Charpy , +23°C	86	kJ/m²	ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C	47	kJ/m²	ISO 179/1eA

Propriedades térmicas	Valor	Unidade	Método de ensaio
ISO Dados
Temperatura de fusão, 10°C/min	280	°C	ISO 11357-1/-3
Temperatura de deflexão térmica, 1.80 MPa	165	°C	ISO 75-1/-2
Temperatura de deflexão térmica, 0.45 MPa	227	°C	ISO 75-1/-2
Temperatura de amolecimento Vicat, B	138	°C	ISO 306
Coef. de expansão térmica linear, paralelo	1	E-6/K	ISO 11359-1/-2
Coef. de expansão térmica linear, perpend.	46	E-6/K	ISO 11359-1/-2
Flamabilidade a espessura h	V-0	class	IEC 60695-11-10

Propriedades elétricas	Valor	Unidade	Método de ensaio
ISO Dados
Constante dielétrica, 100Hz	3.3	-	IEC 62631-2-1
Constante dielétrica, 1MHz	2.7	-	IEC 62631-2-1
Fator de dissipação dielétrica, 100Hz	300	E-4	IEC 62631-2-1
Fator de dissipação dielétrica, 1MHz	160	E-4	IEC 62631-2-1
Resistividade volumétrica específica	1E13	Ohm*m	IEC 62631-3-1
Resistividade superficial específica	1E15	Ohm	IEC 62631-3-2
Resistência elétrica	36	kV/mm	IEC 60243-1

Outras propriedades	Valor	Unidade	Método de ensaio
Densidade	1500	kg/m³	ISO 1183

Diagrama

Características

Processamento

Moldagem por injeção

Forma de entrega

Granulos, Negro, Cor natural

Aditivos

Lubrificantes

Características especiais

Retardante de chama, Estável a luz

Certifications

Contacto com alimentos, Aprovação de alimentos FDA 21 CFR

Disponibilidade regional

América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África

Outras informações

Moldagem por injeção

Vectra resins are well known for their excellent thermal and hydrolytic stability. In order to ensure these properties are optimum, the resin should be dried correctly prior to processing. Vectra A-grades should be dried at 150 C for a minimum of 4 hours in a desiccant dryer.
A three-zone screw evenly divided into feed, compression, and metering zones is preferred. A higher percentage of feed flights may be needed for smaller machines: 1/2 feed, 1/4 compression, 1/4 metering.

Vectra LCPs are shear thinning, their melt viscosity decreases quickly as shear rate increases. For parts that are difficult to fill, the molder can increase the injection velocity to improve melt flow.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.