Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of XAREC® S 143 - (PS-SY)-GF35 - Idemitsu Chemicals
Material Data Center offers the following functions for XAREC® S 143:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Xarec datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our
disclaimer.
| Características de processamento/físicas | Valor | Unidade | Método de ensaio |
| Other Standards[S] |
| Contração após a moldagem, paralelo |
0.2 |
% |
Producer Method |
| Contração após a moldagem, perpendicular |
0.6 |
% |
Producer Method |
| S: | These properties are reported by the producer according standards that are different to our defaults. |
| Propriedades mecânicas | Valor | Unidade | Método de ensaio |
| ISO Dados |
| Módulo de tração |
11300 |
MPa |
ISO 527 |
| Tensão na ruptura |
125 |
MPa |
ISO 527 |
| Deformação na ruptura |
2 |
% |
ISO 527 |
| Módulo de flexão, 23°C |
11000 |
MPa |
ISO 178 |
| Resistência à flexão |
190 |
MPa |
ISO 178 |
| Resistência ao impacto Charpy, +23°C |
40 |
kJ/m² |
ISO 179/1eU |
| Res. impacto Charpy c/entalhe, +23°C |
11 |
kJ/m² |
ISO 179/1eA |
| Resistência ao Impacto Izod, +23°C |
35 |
kJ/m² |
ISO 180/1U |
| Impacto Izod com entalhe, +23°C |
10 |
kJ/m² |
ISO 180/1A |
| Propriedades térmicas | Valor | Unidade | Método de ensaio |
| ISO Dados |
| Temperatura de deflexão térmica, 1.80 MPa |
245 |
°C |
ISO 75-1/-2 |
| Temperatura de deflexão térmica , 0.45 MPa |
265 |
°C |
ISO 75-1/-2 |
| Flamabilidade a espessura h |
HB |
class |
IEC 60695-11-10 |
| Espessuras do tubo de teste |
1.5 |
mm |
- |
| Cartão Amarelo (yellow card) disponível |
sim |
- |
- |
| Propriedades elétricas | Valor | Unidade | Método de ensaio |
| ISO Dados |
| Índice comparativo de linha de fuga |
500 |
- |
IEC 60112 |
| ASTM Dados |
| Resistência elétrica, tempo curto |
45 |
kV/mm |
ASTM D 149 |
| Other Standards[S] |
| Constante dielétrica, 1MHz |
3 |
- |
IEC 60250 |
| Fator de dissipação dielétrica, 1MHz |
10 |
E-4 |
IEC 60250 |
| Resistividade volumétrica específica |
1E14 |
Ohm*m |
IEC 60093 |
| S: | These properties are reported by the producer according standards that are different to our defaults. |
| Outras propriedades | Valor | Unidade | Método de ensaio |
| Densidade |
1300 |
kg/m³ |
ISO 1183 |
| Recomendação de processamento Moldagem por injeção | Valor | Unidade | Método de ensaio |
| Pré-secagem - temperatura |
120 |
°C |
- |
| Pré-secagem - tempo |
3 - 5 |
h |
- |
| Temperatura da massa |
280 - 310 |
°C |
- |
| Temperatura do molde |
130 - 155 |
°C |
- |
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos
Aplicaciones
Automóvel
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.
