Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Iupital FL2010 - (POM+PTFE) - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for Iupital FL2010:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Iupital datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 电性能 - 其它性能 - 加工推荐（注塑）
Any use of this information falls under the rules of our disclaimer.
加工/物理特性价值单位Test Standard
ISO数据
熔体体积流动速度, MVR 6.1 cm³/10min ISO 1133
温度 190 °C -
载荷 2.16 kg -
熔融指数, MFI 7.5 g/10min ISO 1133
温度 190 °C -
负载 2.16 kg -
模塑收缩率, 平行 2.0 % ISO 294-4, 2577
机械性能价值单位Test Standard
ISO数据
拉伸模量 2650 MPa ISO 527
屈服应力 52 MPa ISO 527
屈服伸长率 8 % ISO 527
断裂伸长率 18 % ISO 527
弯曲模量, 23°C 2400 MPa ISO 178
弯曲强度 77 MPa ISO 178
简支梁冲击强度, +23°C 60 kJ/m² ISO 179/1eU
简支梁缺口冲击强度, +23°C 5 kJ/m² ISO 179/1eA
热性能价值单位Test Standard
ISO数据
熔融温度, 10°C/min 166 °C ISO 11357-1/-3
热变形温度, 1.80 MPa 97 °C ISO 75-1/-2
热变形温度, 0.45 MPa 154 °C ISO 75-1/-2
线性热膨胀系数, 平行 110 E-6/K ISO 11359-1/-2
线性热膨胀系数, 垂直 110 E-6/K ISO 11359-1/-2
厚度为h时的燃烧性 HB class IEC 60695-11-10
测试用试样的厚度 0.8 mm -
Yellow Card 现存 是的 - -
电性能价值单位Test Standard
ISO数据
体积电阻率 1E12 Ohm*m IEC 62631-3-1
表面电阻率 1E16 Ohm IEC 62631-3-2
介电强度 25 kV/mm IEC 60243-1
相对漏电起痕指数 600 - IEC 60112
其它性能价值单位Test Standard
吸湿性 0.19 % 类似ISO 62
密度 1460 kg/m³ ISO 1183
加工推荐（注塑）价值单位Test Standard
预干燥-温度 80 °C -
预干燥-时间 3 - 4 h -
模具温度 60 - 80 °C -
1区 170 °C -
2区 180 °C -
3区 190 °C -
喷嘴温度 180 - 210 °C -
螺杆转速 80 - 120 rpm -
注射压力 50 - 100 MPa -
典型数据
加工方法
注塑
添加剂
润滑剂
特征
共聚物
应用
汽车, 电子电气, 通用
地区供应
北美, 欧洲, 亚太, 中南美洲, 中东/非洲
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.