Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NYLENE® 4114 - PA66 - Polymeric Resources Corporation

Material Data Center offers the following functions for NYLENE® 4114:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Nylene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 其它性能 - 加工推荐（注塑）
Any use of this information falls under the rules of our disclaimer.
加工/物理特性价值单位Test Standard
ASTM数据
模压收缩率, 平行 0.014 mm/mm ASTM D 955
机械性能价值单位Test Standard
ASTM数据
拉伸模量 1862 MPa ASTM D 638
拉伸强度 49.6 MPa ASTM D 638
断裂伸长率 60 % ASTM D 638
弯曲模量 1744 MPa ASTM D 790
悬臂梁缺口冲击强度, 1/8 in 859 J/m ASTM D 256
低温悬臂梁缺口冲击强度, Low-Temperature 181 J/m ASTM D 256
温度 -40 °C -
热性能价值单位Test Standard
ASTM数据
DTUL @ 264 psi 60 °C ASTM D 648
熔点 258 °C ASTM D 3418
其它性能价值单位Test Standard
密度 1080 kg/m³ ASTM D 792
加工推荐（注塑）价值单位Test Standard
预干燥-温度 65 - 82 °C -
预干燥-时间 2 - 4 h -
加工湿度 ≤0.2 % -
注塑熔体温度 282 - 304 °C -
模具温度 49 - 93 °C -
1区 260 - 282 °C -
2区 271 - 293 °C -
3区 282 - 304 °C -
喷嘴温度 279 - 301 °C -
注射压力 7 - 15 MPa -
背压 0 - 50 MPa -
保压压力 5 - 12 MPa -
最大停留时间 6 min -
典型数据
加工方法
注塑
特殊性能
高冲击韧性的/经抗冲改性的
特征
共聚物
应用
汽车, 通用
地区供应
北美
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.