Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of CELANEX® 6035GB20 - PBT-GB20 - Celanese

Material Data Center offers the following functions for CELANEX® 6035GB20:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Celanex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 电性能 - 其它性能 - 加工推荐（注塑）
Any use of this information falls under the rules of our disclaimer.
加工/物理特性价值单位Test Standard
ISO数据
模塑收缩率, 平行 1.5 % ISO 294-4, 2577
模塑收缩率, 垂直 1.5 % ISO 294-4, 2577
机械性能价值单位Test Standard
ISO数据
拉伸模量 3300 MPa ISO 527
断裂应力 46 MPa ISO 527
断裂伸长率 8.5 % ISO 527
无缺口简支梁冲击强度, +23°C 22 kJ/m² ISO 179/1eU
简支梁冲击强度, -30°C 19 kJ/m² ISO 179/1eU
简支梁缺口冲击强度, +23°C 1.7 kJ/m² ISO 179/1eA
简支梁缺口冲击强度, -30°C 2.8 kJ/m² ISO 179/1eA
肖氏硬度D 80 - ISO 7619-1
热性能价值单位Test Standard
ISO数据
熔融温度, 10°C/min 225 °C ISO 11357-1/-3
玻璃化转变温度, 10°C/min 50 °C ISO 11357-1/-2
热变形温度, 1.80 MPa 72 °C ISO 75-1/-2
热变形温度, 0.45 MPa 168 °C ISO 75-1/-2
线性热膨胀系数, 平行 77 E-6/K ISO 11359-1/-2
线性热膨胀系数, 垂直 77 E-6/K ISO 11359-1/-2
电性能价值单位Test Standard
ISO数据
相对介电常数., 100Hz 3.7 - IEC 62631-2-1
相对介电常数., 1MHz 3.5 - IEC 62631-2-1
介质损耗因子, 1MHz 170 E-4 IEC 62631-2-1
体积电阻率 >1E13 Ohm*m IEC 62631-3-1
表面电阻率 >1E15 Ohm IEC 62631-3-2
介电强度 30 kV/mm IEC 60243-1
其它性能价值单位Test Standard
吸湿性 0.19 % 类似ISO 62
密度 1460 kg/m³ ISO 1183
加工推荐（注塑）价值单位Test Standard
预干燥-温度 121 °C -
预干燥-时间 4 h -
加工湿度 ≤0.02 % -
注塑熔体温度 235 - 260 °C -
模具温度 65 - 93 °C -
典型数据
加工方法
注塑
供货形式
粒料
其他信息
注塑成型
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30°F (-34°C) at 250°F (121°C) for 4 hours.
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast

Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.