Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUCEL GC225 - POM-GF25 - LG Chem

Material Data Center offers the following functions for LUCEL GC225:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Lucel datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 电性能 - 其它性能 - 加工推荐（注塑）
Any use of this information falls under the rules of our disclaimer.
加工/物理特性价值单位Test Standard
ASTM数据
熔融指数, MFI 10 g/10min ASTM D 1238
温度 190 °C -
负载 2.16 kg -
模压收缩率, 平行 0.0065 mm/mm ASTM D 955
机械性能价值单位Test Standard
ASTM数据
屈服应力 128 MPa ASTM D 638
断裂伸长率 3 % ASTM D 638
弯曲模量 7860 MPa ASTM D 790
弯曲强度 196 MPa ASTM D 790
洛克硬度 R 85 - ASTM D 785
悬臂梁缺口冲击强度, 1/4 in 84.8 J/m ASTM D 256
热性能价值单位Test Standard
ASTM数据
UL94 燃烧性 HB - UL 94
测试厚度 0.75 mm -
DTUL @ 66 psi 165 °C ASTM D 648
DTUL @ 264 psi 160 °C ASTM D 648
电性能价值单位Test Standard
ASTM数据
表面电阻率 1E14 Ohm ASTM D 257
体积电阻率 1E16 Ohm*cm ASTM D 257
其它性能价值单位Test Standard
密度 1590 kg/m³ ASTM D 792
加工推荐（注塑）价值单位Test Standard
预干燥-温度 90 - 110 °C -
预干燥-时间 2 - 3 h -
加工湿度 ≤0.1 % -
注塑熔体温度 210 - 220 °C -
模具温度 60 - 100 °C -
1区 180 - 200 °C -
2区 190 - 210 °C -
3区 200 - 220 °C -
喷嘴温度 200 - 220 °C -
螺杆转速 40 - 75 rpm -
背压 0 - 4 MPa -
典型数据
加工方法
注塑
地区供应
北美, 欧洲, 亚太, 中南美洲
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.